Hi men, welcome back to yet another Gadget Kings video. I'm Abdullah Kabani, owner of a mobile fix employer, and these days we are diving into a immense healing venture: bringing a nicely-abused iPad Pro to come back to life. The back is lined in deep scratches and quite a few dents that make the system appear to be it used to be dragged throughout concrete. Around the the front, the screen is shattered and barely retaining on, and the house button has fallen contained in the iPad and doesn’t paintings. The viewer who despatched this in, who is going through the title Happy Phone from Germana, Australia, purchased the iPad for 50 bucks. It had a display that became past shattered. After replacing the demonstrate, they used it for about every week earlier shedding it on concrete and breaking it, as we see the following. It's a first-new release iPad Pro fashion with 32GB of storage and is running iOS thirteen.0 beta. While the iPad still fairly features, the fingerprint reader has been disabled, and the touch input on the screen doesn’t paintings in all places. Taking a more in-depth take a look at the house button, that you can see its bracket has come unfastened, and there looks a section of paper jammed in there. Since the iPad changed into donated to me, I've made up our minds to head all out and replace the whole damaged components to make it appear to be new lower back. I’d like to thank iFixit for sponsoring this video and imparting me with a new monitor. You can get areas, tools, and guides at iFixit.com/GadgetKings or at the hyperlink below. I ordered the new casing on-line and had the tablet's serial quantity engraved onto the again identical to the original one. It consists of no aspects within, so the whole lot will need to be transferred from the outdated casing. Getting internal this iPad turned into less difficult than widely wide-spread; no heat or prying turned into required as the reveal was so poorly connected I may want to simply elevate it up and out of location. Inside, it doesn’t get tons larger; this is lacking screws and has some ruin to the shields. My wager as to why the display didn’t carry turned into for the reason that the antique adhesive wasn’t wisely wiped clean off. Looking at the home button from the within, I don’t be aware of how to explain this. Maybe it was once to assistance cling the button in position, yet no matter what it was once for, it didn’t work. Next to pop out is the entrance screen. I’ll cast off both screws last in the bracket and disconnect its flex cables. Pulling off the exhibit, we will be able to dispose of any ultimate glass around the perimeter of the iPad. Next, I’ll need to unfasten all of the screws on height of this bracket which is going over the good judgment board. Of direction, there has been additionally a lacking screw in this, so I computer shop GADGET KINGS PRS-(iPhone : iPad : Samsung & Computer service) should now discover two substitute screws while it comes time to reassemble. After disconnecting the battery, it’s now time to take out the 4 screws maintaining within the speaker meeting. While I may believe 4 screws may were adequate, Apple has also delivered a few particularly potent adhesive, and there are a few cables strolling underneath, so that you want to be very cautious wherein you pry. After getting up one part, I determined to just movement directly to hunting down the headphone jack beforehand proceeding to get it solely out. The explanation why for it truly is there’s honestly a cable caught to the speaker assembly at the properly-hand part of the iPad. Once these are got rid of and out of the means of the speaker assembly, I can maintain prying. You can see the adhesive is so reliable that I’m practically snapping this piece of plastic looking to lift it up and out of the iPad. With a couple of minutes of significant prying, I changed into able to do away with the entire assembly unharmed. If you don’t like adhesive, then you’re no longer going to like the subsequent level. It’s time for the good judgment board to pop out, and it’s glued to the casing of the iPad. I’ll first unplug any cables connecting to it previously commencing to pry it out of region. The charging port and top flex cable are soldered onto the board, so you need to take further care around those areas while lifting it up. Of course, we can’t fail to remember to unscrew the lightning connector and attach the speaker wires ahead of pulling the board your entire method out. What I don’t realise is why they used glue to dangle it down. The battery connection is secured with a screw, however the relaxation of the good judgment board isn’t. Back on the accurate, the headphone jack and front digicam desire to be taken out beforehand I can unlock the relax of this flex cable. Finally, the good judgment board will be pulled loose from the casing of the iPad. Sticking with our subject of adhesive, it’s time for that battery to come out. As it connects less than the logic board, we couldn’t remove it in the past. You’re going to desire a substantial amount of alcohol to complete this. The iPad will need a few too, because it will assistance destroy down that glue. In the midsection section of the battery is a flex cable for the smart connector that we’ll desire to unplug. With one half of the battery free, it’s time to start running on the other edge. It’s a same technique and is just as painful. So even whenever you’re now not doing a complete housing alternative and are simply thinking of replacing your iPad’s battery, here's what it takes if you want to get out that battery. Something tells me they virtually don’t need you to. While being not easy to restoration, the whole lot up to now has been going to plan. That changed into approximately to amendment. One little aspect could intent this iPad to remain in portions for the following one year. This is the sensible connector port. Despite being held in with a bracket, it’s also glued in past something I’ve considered. Nothing I threw at it should make it pop out. Eventually, the cable broke off, and the undertaking used to be wear cling except I might get a replacement. The quandary was I couldn’t discover a substitute. The handiest one I ought to in finding changed into black, and that wasn’t going to minimize it. One did pop up for thirty funds, which I purchased, yet my order was canceled shortly after as they didn’t truly have one. Many months later, I stumbled on one on iFixit. Without hesitation, I ordered it, and after all, the challenge may want to proceed. Proceeding, I can take out the rest of the additives within the historical body. There’s not an excessive amount of left, but the speakers down at the underside phase will come out subsequent. At the precise, there’s an extra antenna in order to want to be unscrewed and removed. There are two doors on the left edge of the iPad that I will take off. These are surely hard to get out, and prying at them just bends my instrument. Beneath them are a number of magnets used for the Apple circumstances. I would really like to retrieve them and installation them into the recent casing if I can. I did finally get them out however used to be now confronted with a new trouble. All of the magnets are glued in a bit like all the pieces else. I removed as many as I should but couldn’t get each and every one. The glue become just so potent, and as they’re in one of these rough-to-reach position, this made the procedure even greater tough. On the good-hand part, there had been some more magnets, yet those were secured in so smartly I couldn’t get any of them out. I determined to retain besides via weeding out the digicam, LED flash, microphone, vigor button, and the volume buttons from the higher appropriate-hand corner. After the buttons are out, there's in basic terms one element left: the mesh grilles. They should be would becould very well be connected to the microphones so that you don’t lose them or overlook to connect them later. With that, our iPad is eventually thoroughly disassembled. I have the entirety laid out on two iFixit magnetic mats to keep the constituents organized. In assertion, a variety of these portions have been sitting here for the final year, and I still understand where the whole screws move. It’s time to crack out the brand new casing and start reassembling the iPad, beginning with the speaker grilles. There’s one to be connected in each and every corner. Proceeding, we will attach the antenna and connect its countless Phillips head screws. Then I can move in advance and reattach the amount buttons to the facet of the iPad and glue the microphone to come back into position in the past screwing every thing to come back into place. Next is the vigor button and its flex cable. I’ll reattach the mesh and glue the LED flash to come back into situation. Proceeding, the camera can cross in subsequent earlier we go ahead and glue the complete magnets into the facet of the tablet. For this, I’ll be through liquid adhesive and trying to installation the magnets within the comparable way that they got here out. To determine the ideal alignment of the magnets, I’ll attach an Apple Smart Cover case to the facet of the iPad to determine the whole lot lines up actually. If you permit the glue dry prior to doing this, it's good to emerge as with a clever cover case that doesn’t line up with the iPad. Whilst the glue is drying, I can connect the protecting brackets over the magnets. I actually have to say, whereas disassembly used to be painstaking and not easy, putting it lower back jointly is much less demanding. It has come time to install the common sense board. I’m definitely hoping this iPad nonetheless works after all this time. After all, it hasn’t noticeable persistent in over a 12 months. But beforehand we will be able to try out it out, we nonetheless desire to put in a number of more matters. It’s time to healthy our new sensible connector cable. Before searching this one, I was involved in reverting the iPad again to its historical case simply to make it work, if truth be told giving up on the challenge. But way to iFixit, this side means we can replace the housing. It’s now time to match the new battery into the case. As which you could see, it slides below the board and is aligned with the aid of a pin that sits
